Jewelry Tools
Browse Subcategories
Suspend your beautiful gemstones for display so that they can be seen. This visually appealing display unit allows stones to float. Metal base ensures stability.
You save (%)
Our 4-1/2 -115mm- German cutter specifically designed for multi-strand beading wire is full-flush with jaws induction hardened to 60-62 Rockwell
You save (%)
This assortment of Forme d’Art Sawblades contains 24 each of sizes 4/0, 3/0, 2/0, 0, 1 and 2 for a total of 1 gross.
You save (%)
Sanding sticks (9-7/8″ long x 3/4″ wide) with 5″ x 3/4″ sanding surfaces. Each stick has 10 strips of quality sandpaper (5 on front – 5 on the back) attached in layers. Sturdy plastic construction and non-slip grip. Tear layers off to expose new sanding surfaces. Grits included: 180, 240, 320, 400, 600, 800, 1000, […]
You save (%)
This 33-1/2″ long inner shaft should be used to replace broken or worn shafts on these discontinued motors:
F, JJ, JB.
You save (%)
This 39-1/4″ long inner shaft should be used to replace broken or worn shafts on these discontinued motors:
EE, GG, MMG.
You save (%)
This 39″ long inner shaft comes installed and should be used to replace broken or worn shafts on various motors.
You save (%)
32-5/8″ long, standard material outer sheath comes equipped on ALL Flexades: S.B0-516, S.B0-14, S.B0-12, S.B0-38
You save (%)
37-1/8″ long standard material outer sheath for discontinued EE, GG, MMG geared motors and models 975, 980W, and 981W.
You save (%)
36-1/4″ long, standard material outer sheath comes equipped on most motors.
You save (%)
Pair of motor brushes for Foredom motors. See list inside.
You save (%)
Pair of motor brushes for discontinued CC, DD and MM motors (115 volt only).
You save (%)
Pair of motor brushes for Foredom motors. See list inside.
You save (%)
Replacement collet for H.18, H.18D and H.18SJ Handpieces. Holds accessories with 3/32″ shanks.
You save (%)
Replacement collet for H.10 and H.10D Handpieces. Holds accessories with 3/32″ shanks.
You save (%)
This 1/8″ thick rubber cushion provides an added layer of comfort to H.30 and H.30SJ Handpieces. Grip slides on easily but holds firmly.
You save (%)
The H.8D has the same specs as the H.8, except includes a duplex spring for added flexibility.
You save (%)
The H.8 is a slim collet type handpiece with pre-lubricated ball bearings that require no additional lubrication.
You save (%)
The H.30® general purpose handpiece has prelubricated ball bearings that do NOT require any additional lubrication. Comes with HPCK-0 Chuck Key in molded plastic handle for changing accessories.
You save (%)
Slender, tapered grip H.28 comes with 2 collets and accommodates accessories with shanks up to 1/8″. Key tip connection.
You save (%)
H.18D has the same specs as the H.18, except includes a duplex spring for added flexibility. H.18 is for use with only 2.35mm (3/32″) shank burs.
You save (%)
The H.18 is for use with only 2.35mm (3/32″) shank burs.
You save (%)
H.15D has the same specs as the H.15, except includes a duplex spring for added flexibility.
You save (%)
The H.15 Handpiece has hammering rather than rotary action for use at low speed (0-5,000 rpm) by jewelers for stone setting and decorative work.
You save (%)