Shop
Browse Subcategories
Also known as square handled needle files, these precision files are available in most of the needle file shapes. Overall length is 5-1/2″ (14 cm), length of cut is 1-9/16″ to 2-9/16″ (40 to 65 mm) depending upon shape. Widely used by jewelers, watch makers, die makers, and fine mechanics.
Cut 4
Width: 5/64″ (2.0 mm)
Overall length is 5-1/2″ (14 cm), length of cut is 1-9/16″ to 2-9/16″ (40 to 65 mm) depending upon shape. Widely used by jewelers, watch makers, die makers, and fine mechanics.
Cut 2
Width: 9/64″ (3.7 mm)
Thickness: 3/64″ (1.3 mm)
Overall length is 5-1/2″ (140 mm), length of cut is 1-9/16″ to 2-9/16″ (40 to 65 mm) depending upon shape. Widely used by jewelers, watch makers, die makers, and fine mechanics.
Cut 4
Width: 9/64″ (3.5 mm)
Thickness: 3/64″ (1.0 mm)
Also known as square handled needle files, these precision files are available in most of the needle file shapes. Overall length is 5-1/2″ (14 cm), length of cut is 1-9/16″ to 2-9/16″ (40 to 65 mm) depending upon shape. Widely used by jewelers, watch makers, die makers, and fine mechanics.
Cut 6
Width: 9/64″ (3.7 mm)
Thickness: 3/64″ (1.3 mm)
Also known as square handled needle files, these precision files are available in most of the needle file shapes. Overall length is 5-1/2″ (140 mm), length of cut is 1-9/16″ to 2-9/16″ (40 to 65 mm) depending upon shape. Widely used by jewelers, watch makers, die makers, and fine mechanics.
Cut 4
Width: 9/64″ (3.7 mm)
Thickness: 3/64″ (1.3 mm)
Versatile hammer with interchangeable faces to provide any combination desired. Supplied with two different faces and wrench to tighten or remove collars.
Face Diameter: 9/16″ (14 mm)
Head Length: 2″ (51 mm)
Head Weight: 2 1/2 oz. (71 g)
Designed to fit any straight shaft motor. Made with either right or left-handed threads (for right or left side of motor) and held to shaft by set screws. Threads are clear and deep, and the end is pointed. Steel.
Designed to fit any straight shaft motor. Made with either right or left-handed threads (for right or left side of motor) and held to shaft by set screws. Threads are clear and deep, and the end is pointed. Steel.
Use brass on yellow metals such as copper and brass. Crimped wire is .005″ thick and produces a soft matte like finish. Used for cleaning, deburring, and surface finishing. Precision made, excellent quality. Sold by the dozen.
Metal: Non-Magnetic Stainless Steel
Length: 4-1/2″
Point: Sharp
Mallet is supplied with one flat brass head and one fiber head. Head 2″ (51 mm)
This 39″ long inner shaft comes installed and should be used to replace broken or worn shafts on various motors.
A lightweight vise mounted in a wood handle. Smooth jaws are 1-1/4″ wide and open to 1″. Overall length is 6-1/4″.
Snap those stubborn pins out in a hurry with this clever device.
Flame can be adjusted by raising or lowering slit sleeve. Faceted bowl measures 3 3/16″ in diameter and holds 4 oz. of fuel.
Vigor Super Glue sets in 10 to 20 seconds. Perfect for jewelry repair. Exceptional adhesion for metal, most plastic, ceramic and glass. Pack of 5 – 2 Gram Tubes.
Designed to fit any straight shaft motor. Made with either right or left-handed threads (for right or left side of motor) and held to shaft by set screws. Threads are clear and deep, and the end is pointed. Steel.
Perfect for storing beads, findings and other small parts. Measures: 10-3/4″ x 6-3/8″ x 1-3/4″
No more messy masking tape! These latex rubber sleeves are placed over the flask to contain the investment while pouring and also form a collar so that no spilling occurs.
Yellow abrasive with press-on/flip-off center hole feature. Exclusive grit and backing are designed for jewelry applications and provide exceptionally long life.
Glue bonded, silicon carbide for fast cutting. Far outlasts lapped bands. All are 1/2″ long. Grit textures: COARSE (60); MEDIUM (80); FINE (120).
Designed for polishing small and difficult to reach areas. For use with a mandrel.
Diameter: 2″
Ply: 16
Stitching: 4 Rows
Sold by the dozen
Suitable for all purpose polishing and buffing. Pin hole centers.
Diameter: 4″
Thickness: 1/2″
Soft
Pink Hi-Shine
Size: 5/8″ x 1/8″
Hole: 1/16″
Edge: Square
Sold by the box of 20
Mounted buffs on 3/32″ mandrels. Great for texturing small pieces.
Mounted buffs on 3/32″ mandrels. Great for texturing small pieces.
Made of clay bonded fused silica for melting temperatures up to 2800°F (1538°C).Excellent for melting gold and silver. Diameter: 4″, Depth: 1-3/8″
Size 10 1/2L
3.45mm thick
Hand Size 70/120
4 Eye Chrono hand size 21
Battery 377
Large Envelope Repair Tray, Black 14 3/4″x4″x4″
Lightweight nylon black frame with soft PVC nosepiece. Molded-in side protection offers increased coverage for side impart. Adjustable temples lock into place.
12 pieces per package of yellow gold filled split rings
Jewelry Shield’s specially patented formula lasts much longer than any other product or remedy available. One application lasts three months. 1/2 oz. bottle.